How to Fix HP Printer not Feeding Paper Issue?

If your HP printer restricts to process the feed paper, there might be some issue with the input tray, paper rollers, or with the printing software. Go through the following guidelines and get the solution of the paper feed issue. So, here are some simple steps Fix HP Printer not Feeding Paper issue. Follow these steps prudently. For any technical assistance, dial HP Printer Support Number. Experts will get in touch with you and resolve your issue in a flash.

Fix HP Printer not Feeding Paper

Basic steps to take to get rid of this issue

Given below are the basic steps that you can take to resolve this error. These points are the most effective in terms of getting rid of this issue.

  1. Examine the condition of the paper and reload it

The condition and type of paper can affect the way your printer is picking up the paper. The ends of low-quality paper (the papers that have absorbed the moisture) may twist or lift the paper. Therefore, it does not feed into the printer.

  1. Clean the rollers

Paper fiber, dust, and other debris may collect on the pick rollers and can cause paper feed issue. To avoid this issue, clean the rollers inside the printer and in the duplexer.

  1. Reset the printer

If the above steps fail to fix the issue, then the last option is to reset the printer.

  • Without switching off the printer, detach the power cord from the back of the printer.
  • Wait for 30 seconds, and then connect the power cord again to the back of the printer.
  • Hit the power button to switch on the printer, if it does not power on automatically.

So, these are the methods to solve for HP Printer Paper not Feeding Issue. If you need any assistance, then contact HP Printer Helpline. Experts will sort out all your problem by snapping fingers.

 

Fix 59.F0 error ITB Contact Alienation error HP LaserJet

HP LaserJet color printer is showing 59.F0 Error, and not working appropriately? Are you also dealing with the same issue?  This error is predominantly caused by a transference alienation failure in which the ITB is jammed and incapable to rotate. The SR9 sensor (the prime transfer roller detachment sensor) has gone wicked or the fuser drive assembly has botched. So, the resolution to this situation is described in a thorough manner and step by step elucidation to Fix 59.F0 error ITB Contact Alienation error HP LaserJet is also discussed. So, follow these steps warily. In case of any problem contact HP Number. Experts will get in touch with you and resolve your issue by providing you the simple tips and tricks.

Fix 59.F0 error ITB Contact Alienation error HP LaserJet

Foremost action to overcome this error

Go through the recommended steps to eradicate this blunder.

  • Reset the ITB.
  • If the issue continues, eliminate the ITB totally from the unit and check the ITB gear and flag.
  • Revolve the gear and examine that the flag stimulates when the white gear is rotated.
  • If the ITB flag is smashed or broken, or if the flag is fixed, substitute the ITB.
  • If the ITB gear and flag both are working accordingly, examine the Primary transfer roller detachment sensor SR9 (Sensor K) with the use of the MANUAL SENSOR TEST in the TROUBLESHOOTING MENU.
  • Take away the ITB and fuser assembly to trace Sensor SR9 (3) inside the fuser cavity.
  • From the interior of the fuser cavity, dab and release the SR9 flag to activate the sensor.
  • During pressing and releasing the flag, examine the control panel display for sensor retort (under K) and ensure the sensor toggles between 0 and 1 (0 is the normal state).
  • If the result does not toggle between 0 and 1, replace the sensor (WG85696000CN).

So these are the simplest steps to get rid of this 59.F0 error ITB Contact Alienation error HP LaserJet. You can get HP Printer Assistant to manage your printer device by a utility software. Moreover, get in touch with experts to get immediate help.

 

Align HP Printer with the Help of Certified Experts

If the printer ink fails to line up properly on printouts, or your printer shows an “alignment failed” error message, it might be your printer is out of alignment. You can align your Hewlett-Packard printer by aligning your ink cartridges, resetting your printer, or else using a different type of paper.If you don’t know how to Align Your HP Printer, then read out the blog post from top-to-toe constantly. You will get effectual ideas and can do this task without any hurdle. Moreover, you may also contact HP Printer Service team for getting desired possible solution of this problem.

 

Align HP Printer

Methods to Align Your HP Printer

Go through the below-given instructions carefully as only then you will be able to align your printer and take printouts clear in no time. Have a glance at once:

Method 1: Align Ink Cartridges

  • Power-on your HP printer
  • Load a A-4 size of plain paper into the printer’s input tray
  • Launch the HP Solution Center application on your computer by clicking on “Start” button followed by “Programs” and “HP”
  • Tap on “Settings,” then select “Print Settings” within the HP Solution Center
  • Click on “Printer Toolbox”
  • Click on “Align the Print Cartridges”
  • Click on “Align,” and then follow the on-screen instructions to adjust your printer and properly align the cartridges

Method 2: Reset the Printer

If the above method is not beneficial for you, then jump to the next method that is resetting your printer. Do it with the help of given steps:

  • Turn-on your HP printer
  • Now, disconnect the power cord from the back with keeping the printer powered on
  • Unplug the printer’s power cord from the electrical outlet
  • Wait for a minute and then plug the power cord back into the electrical outlet
  • Reconnect the power cord to the back of your printer
  • Wait for a moment until your printer gets automatically power-on by itself
  • After that print a page to verify that your printer is now properly aligned

Method 3: Making Use of Correct Type of Paper

If the above method is not worked out for you, then use this method:

  • First of all remove all paper from your printer’s input tray
  • Make sure the paper you are loading into the input tray is clean, unused and A4 size
  • Remove any photo, color, or used paper if applicable, and insert the plain white paper to the printer’s input tray
  • Touch the right arrow and select “Setup” from your printer’s control panel home screen
  • Select “Tools”
  • Touch the down arrow and select “Align Printer”
  • Open the top lid of your printer, and place the alignment test page
  • Locate the piece of paper front right corner of the scanner glass
  • Close the lid and press “OK.” Your printer will scan the alignment page
  • Verify the alignment page that it displays a series of marks that are black and blue in color
  • Examine the colored marks to verify that neither of the colors look faded, inconsistent, or streaky
  • Print a test page to assure that your printer is now properly aligned and no longer displays the “alignment failed” error message

Contact Experts If the Problem Continue

Don’t you get satisfied with these given procedures? Want some more handy solution for aligning your HP printer? If yes, then contact HP Support Printer as we have educated and expert tech-geeks who will assist you at reasonable cost. So, don’t worry! Your printer will easily be aligned within a pinch.

Fix HP Deskjet Printers Grinding Noise When It is Printing

Everyone has gone through some or the other problem with their printer, which is why users need the information to resolve the common issues. Several times, troubleshooting printer problems take little more than hasty computer know how and perform the procedural steps. Below is the process to fix HP Deskjet printers grinding noise when it is printing. If you want detailed information about the product, then you can contact HP Printer Support to grab the benefits of being served by the experts. The experts are technicians having full knowledge of the device. They will provide you the best solution to your problem.

Fix HP Deskjet Printers Grinding Noise

The reasons behind this grinding noise

A grinding sound can be heard when the printer is turned on or during printing. Blinking lights may cause noise. The problem may arise because of a carriage stall or a paper jam.

Step by step guide to solve the grinding noise

  1. Turn on the printer.
  2. Release the power cable from the back of the printer.
  3. If the carriage moved to the center, or if the service station is lowered, withdraw the cartridges. Examine the printer for any broken parts.If the carriage did not move to the center, go for manually slide the carriage to the centre. If the carriage is locked either in the right or left position, then proceed to step 5.
  4. Shut the top cover of the printer.
  5. If your printer is HP Deskjet 900 series printer, go to the HP support document removing the cartridges if the printer will not Turn On or if the carriage is frozen (bpd50074).
  6. Remove the rear side door, or the automatic two-sided printing attachment, and look for any paper jams or paper hindrances. Remove all the obstructions.
  7. Check to confirm that the carriage is placed on the right side of the printer. Turn the rear paper guide rollers ascending five times, and then descending four times. If the rollers will freeze, open the top part and slide the carriage towards the right (if it is not present there and if the carriage can move). Try to rotate the rollers again while pushing the clutch in. If again, the rollers do not move, follow the next step.
  8. Swap the rear access door accessory or the automatic two-sided printing accessory. Shut the top cover.
  9. Plug the power cable back to the position.
  10. Turn on the printer, and substitute the cartridges if possible. If the carriage moves, but there is again a grinding noise, then there may be a paper feed issue. In the case, if the carriage will not move, then it is the issue of carriage stall.
  11. After cartridge installation, if the printer is showing a solid power light, then perform a self-test on your printer.

If still, the problem persists, then dial the HP Tech Support Phone Number to take advice from the experts who are technicians having full knowledge of the product and are available for their clients 24/7.

 

Remove HP Printer Scanner Error 13 with Simple Steps

HP printer scanner Error 13 can create huge hindrance that will be the real troublemakers in printing pages.There are many different models of HP printers which are used by the customers, and there are different errors displayed on the screen of the computer, and the meaning of those errors means that the printer is not working in the right way. There are different puzzles, and every puzzle has its solution. Here are the simple steps to remove HP printer scanner error 13. Hence the clients who are dealing with this error and are searching for the solution, so for all of them, here are the steps, so follow the steps gradually.

Apart from this error 13, there are many individual issues like error related to HP printer driver, HP printer paused point or HP printer ink problem and many more. Therefore, for any such type of failure or problem, you can contact HP Support where the experts of HP are ready to serve their customers.

HP Printer Scanner Error 13

Notable steps to remove HP printer scanner error 13

You are proposed to follow the given steps to fix HP Printer Error 13. With the help of these given steps, it will be effortless for you to get rid of the error 13. Therefore, follow the steps gradually.

  • Check the paper

The first step is to examine the entire path to check for the stuck piece of paper.

  • Removing the Paper Tray 2

If you have gone through the above step and it does not work, then remove your printer’s paper tray and the toner cartridge to be safe.

  • Verify Paper Width Sensor Moving

Now it is meant to locate a paper width sensor and should confirm whether that it is moving freely or not.

  • Check Pre-feed Sensor Flag Moving
  1. If the paper feed assembly has separated out, and then check that the pre-feed sensor flag is moving correctly or not.
  2. After this, move to the top of the page sensor and then confirm that the sensor arms are moving freely there or not.
  3. Note: Examine that the pre-feed sensor installed correctly or not.
  • Check Fuser Sensor and Jam

Next you have to locate the fuse sensor and examine the paper jam and attentivelysearch for the possible paper scrap stuck.

  • Replace the DC controller PCA

Then go for replacing the DC controller PCA. Now if the error comes often, then proceed further to the next step as mentioned below.

  • Put the Cartridge and Paper Tray
  1. Next, put a piece of cardboard having the same width of the paper.
  2. Cardboard leaving from the top cavity means you can end it.
  3. After the above process, slowly release the cardboard from the bottom cavity of the printer. After that you have to put the cartridge and paper tray back into the printer and restart your device.

If after going through all these steps, the error does not fix, then do take help from the professionals by contacting HP Printer Helpline Number where experts will solve all your issues and are available 24/7 for you.

 

Resolve Black or Color Ink Not Printing, Other Print Quality Issues

HP Printer is the top quality printing device, which is widely used for different purposes. While printing any document through Hp Printer, you may face different types of errors such as faded printouts, any document with fuzzy or blurred text, color or black ink not printing, ink streaks, and other printing quality troubles. The quality of a printed document is not predicated as printing standards. It is not acceptable. To fix black or color ink not printing or other printing quality errors, HP Printer Help is offered by technical experts to resolve such type of technical difficulties.

 

Resolve Black or Color Ink Not Printing

Install the printer driver again (Windows only)

If you cannot print color from a windows computer system, uninstall and reinstall the printer software.  Skip this step, if your printing machine is able to print in the color.

  • Take out the printing device from the devices list.

To take out printer from the devices list, you need to uninstall the printer software.

  • Go to HP customer support, Software and driver downloads, and installs the new software for your printer.
  • Attempt to print. If these instructions solved error, you don’t need to continue troubleshooting process.

Use real HP ink Cartridges

HP strongly recommends that you use real HP ink or toner supplies. HP cannot assure the quality or constancy of non-HP or refilled cartridges. If you don’t use real HP cartridges, you will not be able to solve the error.

Make sure for ink smears on the back of printouts

If the smears of ink are found on the back of printouts, you can make the best use of an automatic tool to solve the error.

  • Check the printer is fully loaded with the plain white paper.
  • On the printer control panel field, swipe the display to the left side, and touch setup.
  • Touch tools.
  • Swipe up on the “display” button and touch on the clean page smears.
  • The printing machine gradually feeds a blank page
  • Wait for the printing machine to emit the blank page.
  • Attempt to print. If the printing quality is unacceptable, continue to next step to check you’re using the suitable paper for your printing job. Thus by following all these steps, you can resolve HP printer not printing error instantly.

In any case, if the problem still continues then get in touch with a team of certified experts to fix the problem. Your query will be handled by a team technician and you will get complete solution.

How to Add an HP Network Printer on Mac?

HP is a very well-renowned brand in the midst of users for its peripheral devices and software services. HP offers wide range of printers to fulfill the customer’s needs. This list includes Inkjet printers, DeskJet Printers, Color LaserJet printer, LaserJet printers, OfficeJet Printers and Network printers. If you want to print from your HP network printer on your Mac PC, then first you have to add it. If you don’t know the process to add an HP network printer on Mac, then you have to dial HP Printer Help Phone Number at once. The available professionals will surely guide you towards the appropriate steps to fulfill your needs.

Add an HP Network Printer on Mac

Also, you can follow the below mentioned instructions that will help you to add your network printer on Mac.

Let’s begin the procedure of adding an HP network printer on Mac PC:

  • Look for the name of your printer that you would like to add, which might be indicated on the label attached to the printer itself.
  • At the top-left side of your screen, click on the apple menu and select system preferences.
  • From this, click on the printers and scanners.
  • Tap on the +sign to add a printer.
  • Under this, click on IP and in the address field enter the full name of your HP printer.
  • The “USE” drop down will automatically select the associated drivers with your printer model. After that, click on the add button to continue the process.
  • If an error message prompted says, unable to verify the printer on the network then tap on cancel button and move back to the previous step.
  • Next, you will see options box that pop up and the icon just look like your printer. Actually, this is a good sign you are on the right track. Make some changes that you want to do, then press ok.
  • That’s it! If you want to add more printers, then click the + button to continue adding printers.

Hopefully, after trying these steps, you are able to add your HP network printer on Mac. Nevertheless, problem can occur at anytime or anyplace. So, if you encounter any problem related to these steps, then feel free to make a call at HP Support Printer to grab the appropriate guidance of ingenious professionals. As they have years of experience regarding this, they will surely assist you in every possible way.